FDP Home Page / FDP Forum / FAQ's

The FDP is made possible by the following companies and individual members like you.
Please use the links below to show them we value their sponsorship.

Antique Electronics Supply

Amazon

WD Music

Jensen Loudspeakers

Musician's Friend

Guitar Center

Apex Tube Matching

Amplified Parts

Sweetwater

Yellowjackets Tube Converters

MOD KITS DIY


* God bless America and our men and women in uniform *

* Illegitimi non carborundum! *

If you benefit and learn from the FDP and enjoy our site, please help support us and become a Contributing Member or make a Donation today! The FDP counts on YOU to help keep the site going with an annual contribution. It's quick and easy with PayPal. Please do it TODAY!

Chris Greene, Host & Founder

LOST YOUR PASSWORD?

......................................................................

   
FDP Jam
Calendar
Find musicians
in your area!
  Search the Forums  

FDP Forum / Fender Bass Guitars and Bass Amps / fender thumb rest screws

huck

us

Dec 21st, 2016 10:37 AM   Edit   Profile   Print Topic   Search Topic

hi,

do any of you know what size screws i should get to attach a thumb rest to an old musicmaster bass? the holes are already there. just need replacements.

thank you.

Te 52

Laws of Physics

strictly enforced
Dec 21st, 2016 07:00 PM   Edit   Profile   Print Topic   Search Topic

I don't have the exact answer, but here's how I would proceed:

Try dropping drill bits through the hole in the thumbrest until you find the largest one that will go through without binding. Convert that fractional drill diameter to thousandths of an inch (e.g., 5/32"=0.156").

Then use a table (link) to find the closest matching wood screw size.

The length you should be able to estimate by sticking a toothpick into the hole in the body to see how much goes in and adding the amount of screw that is in the thumbrest. Round the figure down to the nearest quarter inch and you should be good.

screw size table

(This message was last edited by Te 52 at 09:01 PM, Dec 21st, 2016)

huck

us

Dec 21st, 2016 10:29 PM   Edit   Profile   Print Topic   Search Topic

THERE'S GOING TO BE MATH?!?

thank you. i'll give it a go.

uncle stack-knob
Contributing Member
**********
****

united kingdom

Dec 30th, 2016 04:07 AM   Edit   Profile   Print Topic   Search Topic

Hello Huck.
Better late than never.

The Fender parts catalogue for 1968 shows bass thumb rest screws as:
part number 015610 "screw sheet metal oval head phillips #5 - 1 inch steel nickel plate.

Out of total anorak interest,the Precision bass at that point is shown as previously using a #6 oval head wood screw by one inch,but being superceded by the #5.
All of this appears to make little sense or matter that much until you compare the actual finger rests and discover that the holes in them changed in size over the years,as reflected by the note above.

Stack-Knob.

huck

us

Dec 30th, 2016 09:37 PM   Edit   Profile   Print Topic   Search Topic

super. thank you. i had planned on taking the bass to lowe's tomorrow to see if i could figure it out.

and to anyone else who's pitched in with advice over the last few years, thank you, too. i just made a contribution to the site for the first time. if you're reading this and haven't contributed, please consider doing so. this is the first and best place i've found for gear info.


Danny Nader

usa

You should have been there!
Jan 2nd, 2017 12:06 PM   Edit   Profile   Print Topic   Search Topic

If you have the thumb rest why take the bass? Just take the thumb rest. If it fits the hole properly, then it needs to be an inch long.

As Uncle sez, oval head phillips, #5 or 6.

Danny

FDP Forum / Fender Bass Guitars and Bass Amps / fender thumb rest screws




Reply to this Topic
Display my email address             Lost your password?
Your Message:
Link Address (URL):
Link Title:




Moderators: Chris Greene  Iron Man  reverendrob  

FDP, LLC Privacy Policy: Your real name, username, and email
are held in confidence and not disclosed to any third parties, sold, or
used for anything other than FDP Forum registration unless you specifically authorize disclosure.

Furtkamp.com 
Internet Application Development

Copyright © 1999-2017 Fender Discussion Page, LLC   All Rights Reserved